he treatment of wastewater can result in a variety of unwanted and hazardous gases Wholesale Calais Campbell Jersey , such as H2S and SO2. As the application specialists, NIS-CO Fan has the expertise needed to supply the proper air moving equipment that is specifically designed for resisting the corrosive nature of these compounds. In other pollution control systems, our fans are installed on the clean side, which offer a higher efficiency design for moving gases into a scrubber or other device. One of the major challenges in wastewater and sewage treatment plants is controlling the odors that are emitted. These plants are often located in residential areas and forced to adhere to strict codes and regulations. These odors are caused by gases such as hydrogen sulfide and ammonia. To reduce odor emissions a variety of systems have been found effective, such as thermal oxidation, chemical scrubbers and biofilters. The fan requirements in these processes are similar in that they require special alloys, coatings or fiberglass construction.
Through decomposition, landfills produce syngas, a combination of methane carbon monoxide Wholesale Leonard Fournette Jersey , and other hazardous gases. To avoid dangerously high levels of these gases, forced draft fans are used to drive fresh air into the landfill mass. Induced draft fans are also used for pulling noxious gases out of the landfill for safe disposal or for collecting them as a fuel source. The fans used in these applications often require special materials or coatings along with spark resistant construction. Depending on your specific needs, Twin City Fan will work with you to select the proper air moving equipment.
High volume, low concentration or non-condensable gases refers to gases that are in concentrations below their explosion limit. These gases are drawn through an induced draft fan and then processed with a RTO (regenerative thermal oxidizer) or incinerator that ultimately burns the gases for safe disposal. HVLC gases are often corrosive and at elevated temperatures, that is why we provide a number of fans that are corrosion resistant. In addition, we offer leak-tight construction to avoid emitting these toxic, flammable gases into the environment. In the case that these gases are above their explosion limit, NIS-CO Fan supplies a full line of non-sparking fans that allow for the safe movement of hazardous gases. Based on your specific requirements, our fans can be constructed with aluminum and monel materials.
In a manufacturing environment Cheap Jermey Parnell Jersey , vacuum systems are used to move and transport waste material. Sawdust, metal shavings, and other waste is easily transported away from work areas to a specified collection point for simplified clean up and removal. Vacuum systems are also used to provide suction for the manipulation of components, various materials and forming processes. These systems usually consist of long runs of relatively small diameter pipe or ducting. This results in the need for high pressure low flow fans.
Boilers are used in a variety of industries for producing heat and energy. Many boiler applications will burn fuel readily available on site, such a byproduct from the given process. An example of this is Bagasse, which is a fibrous matter that remains after sugarcane is processed to extract their juices. The bagasse is a biofuel used for many boiler applications. Fans in boiler applications are forced draft, induced draft, over fire air and combustion air.
At this juncture it is prudent to reiterate that a fan running at a particular speed can have an infinite number of operating points all along its characteristic curve. The fan will interact with the system to produce an operating point at the intersection of the system curve and the fan curve. Note that it is the system in which the fan is installed that will determine the operating point on the fan curve. Thus it is vitally important that the system designer accurately determine the system losses in order to ensure that the actual air flow rate is as close as possible to the design air flow rate.
For additional information please refer to http:www.ventilatingmanufacturers
Oleg Tchechel
Designer of Industrial Process Ventilation Equipment
nis-co@nis-co
NIS-CO Fan Co.
http:www.ventilatingproductsindustrialfan_blowers
http:www.ventilatingproductsventilators A swimming pool will make a fun addition to any home. Instead of getting a ready-built pool, you can design your own pool exactly to your specifications. There are so many factors to take into consideration during the design process that it can be a hard task to know where to start. This article provides some simple tips and tricks on how to design the swimming pool of your dreams.
Size and Location
The first thing to work out is where you want to build the pool. You will want to pick a secluded area if possible Cheap Brandon Linder Jersey , one that is hidden out of the way of roads or footpaths. If this is not an option then you can put up fences, or plant shrubs around the area so that it is private. The next thing to consider is the size of the pool; use a tape measure to measure the length and width of the space that you have available. You can then create a scaled down plan of the area on paper. The size of the pool should depend on the amount of space that you have available, how many people will want to use the pool at any one time, and your total budget.
dzoni 11/07/2013 09:45 selam iz suncane i tople grapske..svi su na broju hvala bogu..svako dobro bosno i hercegovino..PS.11.07.2013..18 GODINA OD STRADANJA SREBRENICE..NEKA IM JE VJECNI RAHMET...
dzoni 30/06/2013 07:28 selam iz suncane grapske..danas su dzenaze HURTIC MEHMEDU I MURATOVIC OSMANU poslije ikindije namaza..rahmet im dusi..svako dobro bosno i hercegovino..
dzoni 21/06/2013 10:22 selam iz vrele i suncane grapske..svi su na broju hvala bogu,,svako dobro bosno i hercegovino..
dzoni 13/06/2013 07:24 selam iz oblacne grapske..svi su na broju hvala bogu..svako dobro bosno i hercegovino..